FUNDAMENTAL PLUMBING GUIDE FOR INSTALLING A BATHTUB

Fundamental Plumbing Guide for Installing a Bathtub

Fundamental Plumbing Guide for Installing a Bathtub

Blog Article

Call Today

They are making several good observations on the subject of Tools You Need to Install a New Bathtub overall in this post down below.


Tools You Need to Install a New Bathtub
Mounting a tub isn't specifically brain surgery, however it does require strong plumbing, carpentry, and sometimes, tiling skills. Changing an old bath tub with a new one is additionally a reasonably challenging task. If the old tub is readily easily accessible, the project can relocate rapidly; if you have to open up a wall surface to eliminate the old tub and position the new bathtub, the task is a lot harder. In either situation, the job is within a home handyman's abilities, although you will certainly require an assistant to move out the old bathtub and set in the brand-new one. Make sure you have qualified yourself for the work and also fit trying it. As opposed to working with a contractor to take over a halfway-completed task, it is far better to think about utilizing one before you start. Possibilities are you may require a specialist plumber to make tube links.
This post will help you set up a new bathtub in your bathroom if you have actually already bought a brand-new tub and don't require to transform the plan of your previous supply of water pipes.
Your devices and also material checklist need to comprise the following:
  • New Bath tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipeline Caps


  • Removing Old Taps


    If you require to replace old faucets with new ones as a part of your setup, then the first thing you must do is detach the water supply. After doing so, switch on the taps to drain pipes any water remaining in the system. The procedure of removing the existing taps can be quite problematic as a result of the limited gain access to that is often the case.
    Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will originate from the pipes. As soon as the supply pipelines have been gotten rid of, make use of the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from turning throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing substance.
    Prior to moving on to fit the brand-new taps, compare the pipeline connections on the old taps to the new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.

    Suitable New Taps


    If the tails of the new taps are plastic, then you will need a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end provides a link to the existent supply pipelines.
    If you need to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
    Next, place the tap in the placing hole in the bath/basin making sure that the washing machines are in place in between the faucet and the sink. Protect the faucet in position with the supplier offered backnut. When the faucet is safely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet ports. The former type should be linked to the tap ends first, tightening just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.

    Installing the Bath tub


    Making use of both wood boards under its feet, put the tub in the called for placement. The wooden boards are practical in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto 4 tiny factors.
    The following objective is to guarantee that the bathtub is leveled all round. This can be attained by checking the level as well as adjusting the feet on the bathtub till the spirit level reads level.
    To set up taps, fit all-time low of the outermost adaptable tap adapter to the suitable supply pipeline by making a compression join; then do the exact same for the various other tap.
    Activate the water and also examine all joints and brand-new pipework for leakages as well as tighten them if required. Fill up the bathtub and additionally examine the overflow electrical outlet and the normal outlet for leakages.
    Finally, take care of the bath paneling as described in the producer's instruction manual. Tiling and sealing around the bath tub ought to wait up until the bathtub has actually been utilized at the very least once as this will certainly settle it into its final setting.

    Getting ready for the Installment


    First of all, the supporting frame provided with the bathroom needs to be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to make certain that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps unit to avoid strain on the bathtub.
    Fit the flexible tap connectors to the bottom of both taps utilizing 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you make use of every one of the supplied washing machines.
    Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently prepare to be suited its last position.

    Tiling Around the Tub


    In the location where the bath meets the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to crack a rigid seal, causing the water to penetrate the wall between the bath and also the tiling, leading to complications with wetness and also feasible leaks to the ceiling below.
    You can pick from a selection of coloured sealants to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to securing, to allow for the motion experienced when the bathtub is in usage. The sealer can split rather early if you do not take into account this motion before sealing.
    Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise quickly available on the market. It is a good idea to fit the ceramic tiles utilizing waterproof or water-proof glue and also cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Tools You Need to Install a New Bathtub

    I found that write up on Installing A Bathtub while doing a lookup on the internet. Sharing is nice. Who knows, you will be helping someone out. We appreciate reading our article about How to Install a Bathtub Yourself.


    Schedule And Pricing

    Report this page